NetBSD 1.5_ALPHA2 (GO61923) #0: Sun Sep 10 16:41:27 BST 2000 nick@go61923:/usr/NetBSD/NetBSD-1.5/src/sys/arch/i386/compile/GO61923 cpu0: Intel Pentium III (E) (686-class) total memory = 127 MB avail memory = 114 MB using 1657 buffers containing 6628 KB of memory BIOS32 rev. 0 found at 0xfd790 PCI BIOS rev. 2.1 found at 0xfd9cb PCI IRQ Routing Table rev. 1.0 found at 0xfdf50, size 144 bytes (7 entries) PCI Interrupt Router at 000:07:0 (Intel 82371FB PCI-to-ISA Bridge (PIIX)) pci_addr_fixup: 000:04:0 0x104c 0xac1c new address 0x08000000 pci_addr_fixup: 000:04:1 0x104c 0xac1c new address 0x08001000 mainbus0 (root) pci0 at mainbus0 bus 0: configuration mode 1 pci0: i/o space, memory space enabled pchb0 at pci0 dev 0 function 0 pchb0: Intel 82443BX Host Bridge/Controller (rev. 0x03) ppb0 at pci0 dev 1 function 0: Intel 82443BX AGP Interface (rev. 0x03) pci1 at ppb0 bus 1 pci1: i/o space, memory space enabled vga0 at pci1 dev 0 function 0: ATI Technologies Mach64 LM (rev. 0x64) wsdisplay0 at vga0: console (80x25, vt100 emulation) cbb0 at pci0 dev 4 function 0: Texas Instruments PCI1225 PCI-CardBus Bridge (rev. 0x01) cbb1 at pci0 dev 4 function 1: Texas Instruments PCI1225 PCI-CardBus Bridge (rev. 0x01) pcib0 at pci0 dev 7 function 0 pcib0: Intel 82371AB PCI-to-ISA Bridge (PIIX4) (rev. 0x02) pciide0 at pci0 dev 7 function 1: Intel 82371AB IDE controller (PIIX4) (rev. 0x01) pciide0: bus-master DMA support present pciide0: primary channel wired to compatibility mode wd0 at pciide0 channel 0 drive 0: wd0: drive supports 16-sector pio transfers, lba addressing wd0: 11513 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 23579136 sectors wd0: 32-bit data port wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 pciide0: primary channel interrupting at irq 14 wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data transfers) pciide0: secondary channel wired to compatibility mode pciide0: disabling secondary channel (no drives) uhci0 at pci0 dev 7 function 2: Intel 82371AB USB Host Controller (PIIX4) (rev. 0x01) uhci0: interrupting at irq 10 usb0 at uhci0: USB revision 1.0 uhub0 at usb0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered Intel 82371AB Power Management Controller (PIIX4) (miscellaneous bridge, revision 0x03) at pci0 dev 7 function 3 not configured esm0 at pci0 dev 8 function 0: ESS Maestro 2E (rev 16) esm0: interrupting at irq 10 esm0: SigmaTel STAC9721 codec; 18 bit DAC, 18 bit ADC, Rockwell 3D audio0 at esm0: full duplex, mmap, independent mpu0 at esm0 midi at mpu0 not configured cbb0: interrupting at irq 10 cbb0: cacheline 0x8 lattimer 0x20 cbb0: bhlc 0x824008 lscp 0x20020200 cardslot0 at cbb0 slot 0 flags 0 cardbus0 at cardslot0: bus 2 device 0 cacheline 0x8, lattimer 0x20 pcmcia0 at cardslot0 cbb1: interrupting at irq 10 cbb1: cacheline 0x8 lattimer 0x20 cbb1: bhlc 0x824008 lscp 0x20030300 cardslot1 at cbb1 slot 1 flags 0 cardbus1 at cardslot1: bus 3 device 0 cacheline 0x8, lattimer 0x20 pcmcia1 at cardslot1 isa0 at pcib0 com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo pckbc0 at isa0 port 0x60-0x64 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pms0 at pckbc0 (aux slot) pckbc0: using irq 12 for aux slot wsmouse0 at pms0 mux 0 lpt0 at isa0 port 0x378-0x37b irq 7 pcppi0 at isa0 port 0x61 sysbeep0 at pcppi0 npx0 at isa0 port 0xf0-0xff: using exception 16 fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2 fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec apm0 at mainbus0: Power Management spec V1.2 biomask ef6d netmask ef6d ttymask ffef com3 at pcmcia0 function 0: serial device com3: ns16550a, working fifo ep0 at pcmcia1 function 0: 3Com 3c574-TX 10/100Mbps Ethernet ep0: address 00:50:da:e4:80:3b, 64KB word-wide FIFO, 1:1 Rx:Tx split tqphy0 at ep0 phy 0: 78Q2120 10/100 media interface, rev. 10 tqphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto boot device: wd0 root on wd0a dumps on wd0b root file system type: ffs wsdisplay0: screen 1 added (80x25, vt100 emulation) wsdisplay0: screen 2 added (80x25, vt100 emulation) wsdisplay0: screen 3 added (80x25, vt100 emulation) wsdisplay0: screen 4 added (80x25, vt100 emulation) wsmux1: connecting to wsdisplay0